New High Performance Analog Products for May


If you are unable to see the message below, click here to view.

High-Performance Analog

Connection
Your monthly update of new Analog products from TI


Texas Instruments

To subscribe to the TI Analog Connection eNewsletter, please click here.
May 2014


Amplifiers and Linear
36-V programmable-gain, voltage-output, bi-directional, zero-drift series current-shunt monitor
The INA225 is a voltage-output, current-sense amplifier that senses drops across current-sensing resistors at common-mode voltages that can vary from 0 V to 36 V, independent of the supply voltage. The device is a bidirectional, current-shunt monitor that allows an external reference to be used to measure current flowing in both directions across a current-sensing resistor.
Resources: Datasheet, INA225 TINA-TI reference design, INA225 TINA-TI spice model, INA225 evaluation module for 36-V programmable-gain, current shunt monitor

  • High accuracy minimizes system margins and remain constant over temperature
  • Accurate monitoring with wide dynamic range for high peak currents
  • Applications: Power supplies, motor control, computers, telecom equipment, power management, test and measurement
INA225: 1KU pricing: INA225AIDGKR $0.99, INA225AIDGKT $1.14
High- or low-side, bi-directional current sense comparator
The INA300 is a high common-mode, current-sensing comparator that is configured to detect overcurrent conditions through measuring the voltage developed across a current sensing or shunt resistor. The device can measure this differential voltage signal on common-mode voltages that can vary from 0 V up to 36 V, independent of the supply voltage.
Resources: Datasheet, functional diagram, INA300 TINA-TI reference design, INA300 TINA-TI spice model, evaluation module

  • Simple current trip point solution provides complete over-current detection block
  • BoM savings over discrete solutions
  • Applications: Over-current detection, servers/computers, power supply protection, circuit breaker, battery management, telecom equipment
INA300: 1KU pricing: INA300AIDSQR $0.70, INA300AIDSQT $0.81
Data Converters
Inductance-to-digital converter with SPI interface
Inductive sensing is a contactless, short-range sensing technology enabling high-resolution and low-cost position sensing of conductive targets, even in harsh environments. Using a coil or spring as a sensor, the LDC1041 inductance-to-digital converter provides system designers a way to achieve high performance and reliability at a lower system cost than other competing solutions.
Resources: Datasheet, evaluation module, LDC1000 EVM software GUI, LDC1051 evaluation module, LDC1000 EVM software GUI

  • Supports wide array of sense elements-wound, printed or discrete (ferrite-enhanced or air-core)
  • Allows the sensor to be located remotely from the electronics, isolating the IC from harsh environments, or when using existing components in the system as sensors (e.g., springs) which do not provide real-estate for IC placement.
  • Applications: Axial and lateral distance sensing, angular position/rotational sensing, event counting, spring motion sensing,cConductive target presence detection
LDC1041 / 51: 1KU pricing: LDC1041NHRJ $2.50, LDC1041NHRR $2.50, LDC1041NHRT $2.88, LDC1051NHRJ $1.92, LDC1051NHRR $1.92, LDC1051NHRT $2.21
12-bit high-density analog monitor and control (AMC) solution
The AMC7832 is a highly integrated, low-power, analog monitoring and control solution that includes a 17-channel, 12-bit analog-to-digital converter (ADC) with programmable alarms, twelve 12-bit digital-to-analog converters (DACs) with output ranges of either 0 to +5-V, 0 to +10-V or –10 to 0-V, eight GPIOs, internal reference and a local temperature sensor channel. The AMC7832 high level of integration significantly reduces component count and simplifies closed-loop system designs.
Resources: Datasheet, evaluation module

  • Addresses the transition of RF power amplifiers to GaN FETs by including the bipolar selectable output voltage ranges as well as bipolar input ranges
  • Saves board space, reducing design time and minimizing layout effort while reducing costs
  • Applications: Cellular basestations, microwave backhaul, optical networking, test and measurement solutions, data acquisition
AMC7832: 1KU pricing: AMC7832IPAP $16.95, AMC7832IPAPR $14.95
Low-noise, high-gain, three-channel AFE for thermopile sensors
The LMP93601 is an optimized analog front-end (AFE) for occupancy detecting thermopile arrays up to 16 x 16 and thermopile mass flow sensors. The AFE combines excellent noise performance, low offset voltage, high gain, and low-power consumption at sampling rates ideal for monitoring thermopile sensors.
Resources: Datasheet, IBIS model, evaluation module, GUI software for LMP93601EVM

  • Programmable gain up to 4096x gains up small sensor signals
  • Low noise performance provides low noise signal reading from small sensor output signals
  • Applications: Thermopile array sensors, thermocouple flow sensors, occupancy detection, gesture recognition, HVAC, lighting control
LMP93601: 1KU pricing: LMP93601NHZR $3.05, LMP93601NHZT $3.51
256-channel analog front-end for flat-panel digital x-ray detector
The AFE1256 is a 256-channel, analog front-end (AFE) designed to suit the requirements of flat-panel detectors (FPDs) based on digital X-ray systems. The device includes 256 integrators, a programmable gain amplifier (PGA) for full-scale, charge-level selection, a correlated double sampler (CDS) with dual banking, 256:4 analog multiplexers, and four 16-bit, successive-approximation register (SAR) analog-to-digital converters (ADCs) onboard. Serial data from the ADCs are available in SPI™ format.
Resources: Datasheet, evaluation module, functional diagram

  • 256 channels with on-chip 16-bit ADC: higher integration for smallest system footprint
  • Noise: 758 eRMS with 28-pF sensor capacitor in 1.2pC range: lowest noise ensures highest image quality
  • Applications: Digital radiography, CT scanners, baggage scanners, infrared spectroscopy
AFE1256: 1KU pricing: AFE1256GBTD $68.00, AFE1256TDS $120.00
Automotive, 14.4kSPS, 24-bit ADC with integrated low-drift reference
The ADS1259-Q1 is a precision, low-drift, 24-bit, analog-to-digital converter (ADC). The device can perform conversions at data rates up to 14.4 kSPS with high resolution and is therefore ideally suited to measure rapidly changing signals that have a wide dynamic range. An integrated low-noise, low-drift 2.5-V reference eliminates the need for an external voltage reference, thus reducing system cost and component count.
Resources: Datasheet, IBIS model

  • Programmable data rate from 10 SPS to 14.4kSPS allows for optimization of noise vs. data rate
  • High resolution: 21.3 ENOB at 1.2kSPS allows measurement of signals with wide dynamic ranges
  • Applications: Automotive power train, electrical vehicles, other automotive applications
ADS1259-Q1: 1KU pricing: ADS1259QPWRQ1 $6.55
Quad-channel, 16-bit, 1.6/2.5 GSPS, DAC with JESD204B interface
The terminal-compatible DAC37J84/DAC38J84 family is a low power, 16-bit, quad-channel, 1.6/2.5 GSPS digital to analog converter (DAC) with JESD204B interface.
Resources: Datasheet, IBIS model, DAC37J84 evaluation module, TSW14J56EVM evaluation module, DAC3XJ8XEVM software, high-speed data converter pro software, functional diagram

  • Enables wideband transmit over two antenna simultaneously
  • Provides 500MHz of information bandwidth per path, or 1GHz per complex path
  • Applications: Wireless infrastructure, wireless backhaul, point-to-point microwave, software-defined radio, test and measurement
DAC37J84 / DAC38J84: 1KU pricing: DAC37J84IAAV $80.50, DAC37J84IAAVR $79.00, DAC38J84IAAV $121.50, DAC38J84IAAVR $120.00
Dual temperature-controlled DAC with integrated EEPROM + output ON/OFF control
The LMP92066 is a highly-integrated dual temperature controlled DAC solution for autonomous temperature compensation of bias voltages and currents. Two arbitrary temperature-to-voltage transfer functions are stored in the internal EEPROM as look-up-tables. Once powered up, the device operates autonomously of the system in providing pre-programmed temperature dependent output.
Resources: Datasheet, IBIS model, evaluation module, LMP92066 GUI

  • Dual temperature-controlled 12-bit DACs allows for the temperature compensation of bias voltages and currents
  • Integrated EEPROM for the LUT control loop allows the LMP92066 to be programmed during production testing and the device to be fully functional in the field without processor intervention after power up
  • Applications: GaN or LDMOS PA bias controller, sensor temperature compensation, timing circuit temperature compensation
LMP92066: 1KU pricing: LMP92066PWP $2.99, LMP92066PWPR $2.49
Switches and Multiplexers
Ultra-low rON, 6-A, Load Switch with Quick Output Discharge
The TPS22961 is a small, ultra-low RON, single channel load switch with controlled turn on. The device contains an N-channel MOSFET that can operate over an input voltage range of 0.8V to 3.5V and can support a maximum continuous current of 6A.
Resources: Datasheet, PSpice transient model, evaluation module

  • VIN range suitable for low voltage processor rails
  • Minimum voltage drop through pass FET for tighter tolerance voltage rails (lower IR drop)
  • Applications: Ultrabook/notebooks, tablet PC, set-top boxes, Chromebooks, telecom systems, servers
TPS22961: 1KU pricing: TPS22961DNYR $0.54, TPS22961DNYT $0.62
Interface
USB 3.0 single-channel, re-driver with equalization
The TUSB551 is a 4th-generation USB3.0 SuperSpeed (SS) re-driver that features a 1.8V power supply with low consumption, superior output drive performance, and automatic LFPS De-Emphasis control for full USB 3.0 compliance. The re-driver offers selectable gain settings in the equalizer to account for channel loss.
Resources:
Datasheet, HSPICE model, functional diagram
  • 35% smaller form factor enables smaller designs for space constrained applications
  • 20% lower power extends battery life and allows smaller battery implementation
  • Applications: Smartphone, notebook PC, tablet: multimedia
TUSB551: 1KU pricing: TUSB551RWBR $1.50
Power Management
Pack-side Impedance Track™ fuel gauge | Battery gas gauge
The bq27411-G1 is an easy-to-configure fuel gauging solution for single series cell Li-Ion battery packs. The device requires minimal configuration and uses one time programmable (OTP) non-volatile memory (NVM) to avoid an initialization download by the system processor.
Resources:
Datasheet, evaluation module, pack-side Impedance Track™ fuel (gas) gauge evaluation module, GaugeStudio for selected single-cell gauges, functional diagram
  • Enables design of a host free fuel gauge with minimal host intervention
  • Enables lower terminate voltage of system and extends run time from battery
  • Applications: Cellular phones, PDA and smart phones, MP3 players, digital cameras, internet appliances, handheld devices
BQ27411-G1: 1KU pricing: BQ27411DRZR-G1A $1.15, BQ27411DRZR-G1C $1.15, BQ27411DRZT-G1A $1.32, BQ27411DRZT-G1C $1.32
System-side Impedance Track™ battery fuel (gas) gauge
The Texas Instruments bq27441-G1 is an easy to configure microcontroller peripheral that provides system-side fuel gauging for single-cell Li-Ion batteries. The device requires minimal user configuration and system microcontroller firmware development.
Resources:
Datasheet, evaluation module, GaugeStudio for selected single-cell gauges
  • Enables design of a host free fuel gauge with minimal host intervention
  • Enables lower terminate voltage of system and extends run time from battery.
  • Applications: Mobile phones, portable audio, digital still camera, internet appliance, personal digital assistant (PDA)
BQ27441-G1: 1KU pricing: BQ27441DRZR-G1B $1.15, BQ27441DRZT-G1B $1.32
Single-cell, Li-Ion battery fuel gauge with integrated protection
The Texas Instruments bq27742-G1 is a fuel gauge for single-cell Li-ion battery packs that uses patented Impedance Track technology to deliver rate-, temperature-, and aging-compensated predictions of remaining battery capacity and system runtime with highest accuracy. The device also includes a fully integrated high-side protector that eliminates the need for a separate Li-ion protection circuit and provides a full suite of high-accuracy fault detections for overvoltage, undervoltage, overcurrent in charge, overcurrent in discharge, and short-circuit in discharge conditions.
Resources:
Datasheet, evaluation module, Battery Management Studio, functional diagram
  • Enables design of a host free fuel gauge with minimal host intervention
  • Enables lower terminate voltage of system and extends run time from battery.
  • Applications: Cellular phones, MP3 players, PDA and smart phones, handheld devices, digital cameras, internet appliances
BQ27742-G1: 1KU pricing: BQ27742YZFR-G1 $1.45, BQ27742YZFT-G1 $1.67
2.5-A and 5-A, 35-VMAX VDD FET and IGBT single-gate driver
The UCC27532-Q1 device is a single-channel high-speed gate driver capable of effectively driving MOSFET and IGBT power switches by up to 2.5-A source and 5-A sink (asymmetrical drive) peak current. Strong sink capability in asymmetrical drive boosts immunity against parasitic Miller turn on effect.
Resources:
Datasheet, Gate driver daughter card with isolation based on UCC27532
  • Improved immunity against Miller C*dV/dt turn-on events and negative input voltage handling for ground bouncing issues
  • Allows easy, independent optimization of turn-on and turn-off speeds
  • Applications: Companion to digital power controllers, automotive applications, gate drive for emerging WBG power device, superior replacement to discrete components
UCC27532-Q1: 1KU pricing: UCC27532QDBVRQ1 $0.88
High-power flyback controller with primary-side regulation and peak power mode
The UCC28630 targets high-power, primary-side regulated flyback converters. The powerful gate driver and ability to operate in both CCM and DCM make the device suitable for applications with a wide power range. The peak power mode allows transient peak power delivery up to 200% of nominal rating, with only a 25% peak current increase, maximizing transformer utilization.
Resources:
Datasheet, evaluation module, functional diagram
  • Eliminates optocoupler feedback circuit and associated components which help reduce part count and overall system cost. Also increases reliability of power supply by eliminating opto.
  • Best-in-class for primary-side regulators without the need for opto feedback circuit
  • Applications: AC-DC adapters for notebook, game consoles and printers, open frame SMPS for industrial, printer, white goods and LCD monitors, energy-efficient AC-DC supplies for nominal power 10-W to 65-W (with up to 200% transient peak power)
UCC28630: 1KU pricing: UCC28630D $0.72, UCC28630DR $0.60
60A synchronous buck NexFET™ smart power stage
The CSD95372BQ5M NexFET smart power stage is a highly optimized design for use in a high power, high density Synchronous Buck converter. This product integrates the Driver IC and Power MOSFETs to complete the power stage switching function. This combination produces high current, high efficiency, and high speed switching capability in a small 5- x 6-mm outline package.
Resources:
Datasheet, PSpice model, functional diagram
  • Delivers higher efficiency in a typical high current POL design
  • Enables higher switching frequency and improved transient response for less output capacitors. Reduction in size of the output filter (caps and inductor)
  • Applications: Multiphase synchronous buck converters, high-frequency applications, high current, low duty cycle applications; POL DC-DC converters; memory and graphic cards: desktop and server VR11.x/VR12.x V-core and memory synchronous converters
CSD95372BQ5M: 1KU pricing: CSD95372BQ5M $2.19
3A, 30V, host-controlled, single-input, single-cell switchmode Li-Ion battery charger with USB OTG
The bq24260/bq24261/bq24262 are highly integrated single cell Li-Ion battery charger and system power path management devices that supports operation from either a USB port or wall adapter supply.
Resources:
Datasheet, evaluation module
  • Allows for flexible design management
  • Power path option allows the user to power the system while simultaneously charging battery
  • Applications: Portable media players, digital still cameras, portable handheld devices, tablets and e-readers, multimedia players, low-power handhelds
BQ24260 / 61: 1KU pricing: BQ24260YFFR $1.95, BQ24260YFFT $2.24, BQ24261YFFR $1.95, BQ24261YFFT $2.24
500mA 30W anode-capable constant current buck LED driver
The TPS92511 is an easy-to-use 65V constant current buck converter for driving a single LED string with current up to 0.5A and efficiency up to 95%. Only five external components are required for basic operation and single layer PCB layout is feasible because of the integration of an N-MOSFET, no external current sensing resistor, no external compensation and the proper terminal assignment.
Resources:
Datasheet, PSpice transient model, evaluation board
  • Reduced wiring complexity
  • Circuit can be adapted for a wide input voltage range
  • Applications: Under 30W LED luminaires / lamps, intelligent lighting with PWM dimming, second-stage lighting for ceiling lamp, architectural and display lighting
TPS92511: 1KU pricing: TPS92511DDA $0.72, TPS92511DDAR $0.60
High-efficiency MicroSiP™ step-down converter module
TPS8269xSIP is a fully-integrated, high-frequency device (no external inductor and Input/output capacitor needed). It is the smallest 800mA solution in the market with over 90% efficiency and lowest quiescent current, 23uA. It is ideal for applications where space limitations are critical and performance and efficiency is a must have. Given the integration of the external devices, TPS8269xSIP becomes a 1-Stop-Shop for customers. In addition, typical general concerns and challenges on how to select and layout the external components are not existing anymore, due to their integration inside TPS8269xSIP. The Spread Spectrum (PWM Frequency Dithering) combined with the high PSRR makes the part ideal for noise-sensitive applications like audio and imaging devices. The device is a great fit where performance and solution size matter!
Resources:
Datasheet
  • Allows for 6.7mm2 solution size, thus provides 110mA/mm2
  • Supports noise sensitive applications through improved RF spurious performance and radiated noise reduction
  • Applications: Smart phones, camera modules, fiber optics, memory supply, digital TV, WLAN, GPS and Bluetooth applications, wearable healthcare and fitness gear, building management: sensors, metering, surveillance, automation
TPS826951 / 692: 1KU pricing: TPS826951SIPR $1.50, TPS826951SIPT $1.73, TPS82692SIPR $1.50, TPS82692SIPT $1.73
TI Technical Blogs
TI Precision Designs Hub
Check out The Signal, TI's analog signal processing circuits and solutions blog focused on technical topics, such as:
 •
 •

Power House
Read the latest posts on Power House - Trends, topics and musings in Power Management:
 •
 •

Analog Wire
Learn the latest on analog signal chain solutions to real-world problems on TI's signal chain blog:
 •
 •

Fully Charged
The latest power trends for battery-powered designs:
 •
 •

Motor Drive & Control
TI spins motors: smarter, safer greener.
 •

On Board with Bonnie
Navigating analog signal chain designs with Bonnie Baker.
 •
New Literature and Videos
Application Notes:
 •
 •
 •
 •
 •
Selection Guides:
 •
Videos:
 •
 •
 •
 •
 •
 •
 •
Company-Authored Articles in the Media
 •
"Rapid charging for battery-powered portable devices," by Jinrong Qian and Michelle Li. Battery Power Magazine. February 2014.
 •
"Maximizing the output power from thermoelectroc harvesters," by Yogesh Ramadass. Wireless Design & Development. February 2014.
 •
"Power Line Communication Implementation for DC Applications," by Ahinder Sing and Dave Hermann. EDN. February 2014.
 •
 •
"Use current measurement as a leading indicator for system thermal management," by Dan Harmon, Electronic Design. February 2014.
Customer Support Contact Information
Visit TI's E2E™ Community and interact with your peer engineers, TI engineers, and other experts in order to ask questions, share knowledge, explore ideas, and help solve problems.
Product Information Centers
 •
 •
 •
 •
To subscribe to the TI Analog Connection eNewsletter, please click here.
Also, you can subscribe to my.ti news here.

Google Play
App Store
TI Mobile
Facebook
Twitter
LinkedIn
Subscribe

Postagens mais visitadas deste blog

Programação de um CLP: Modos de programação

The Mystery of USB Chargers

STRONG SRT 4622 Satellite TV Receiver Repaired