Take a closer look | i.MX 6ULL Applications Processor

-

 

 

NXP

DOWNLOAD REFERENCE MANUAL ›

 
NXP

 

 

date

i.MX 6ULL
Applications Processor Reference Manual

 

 

Download Now  ›

 

 

The i.MX 6ULL is a power efficient and cost-optimized applications processor family featuring an advanced implementation of a single Arm Cortex-A7 core, which operates at speeds up to 900 MHz.

The i.MX 6ULL applications processor includes an integrated power management module that reduces the complexity of an external power supply and simplifies power sequencing. Each processor in this family provides various memory interfaces, including 16-bit LPDDR2, DDR3, DDR3L, raw and managed NAND flash, NOR flash, eMMC, Quad SPI and a wide range of other interfaces for connecting peripherals such as WLAN, Bluetooth®, GPS, displays and camera sensors.

Take a closer look at the reference manual to see how the product can work for you.

 

 

Download Reference Manual ›

 

 

.

.

.

© 2023 NXP B.V. All rights reserved.

.

 

 

Postagens mais visitadas deste blog

Programação de um CLP: Modos de programação

-
Imagem
No seguimento do curso de Automação, neste artigo apresento como perceber os conceitos básicos de programação de um CLP. No decorrer das próximas edições apresentaremos a forma de programar um controlador lógico programável Autores: Filipe Pereira - Eng. Elétrotécnico / Automação Klean Energie 4 Life, Ltda Energias Renováveis - Portugal As linguagens de programação são empregadas nos CLPs desde que estes surgiram em 1960. Estas permitem ao usuário inserir programas de controle utilizando sintaxes pré-estabelecidas. Previamente ao estudo dos três tipos de linguagem mais utilizados na programação de CLPs, convém rever alguns conceitos essenciais. O programa que vai definir o automatismo é constituído por uma série de instruções e funções onde são operados os bits de memória. Estas instruções e funções, serão introduzidas na memória do CLP, através de um periférico destinado a esse fim e que poderá ser uma console de programação ou software específico para PC. Veja na figura 1 u...
Leia mais

Subwoofer Repair

-
Imagem
By  Jestine Yong  on December 3, 2013   A customer brought this powered speaker for repair. It is a Wharfedale Titan 12’ subwoofer Amplifier. The complaint: No power. I opened the unit checking the usual things such as the fuse, EMI filter coils, voltage on filter caps etc. These all checked out fine, and I measured 320VDC over the two filter caps. The unit uses a SMPS. The smps and class-D Amplifier, are both on the same board. I then connected my analog meter to one of the secondary output lines going to the amplifier. There was no voltage here, and nothing on any of the other output lines going to the pre-amp board. I then proceeded to check if it is a shutdown problem, by switching the unit on and watching to see if the needle on my analog meter jumps up for a brief moment. No movement at all. This made me believe I have a primary –side fault. I checked the two, main switching Mosfets  and they were good. From the below photo you can ...
Leia mais

STRONG SRT 4622 Satellite TV Receiver Repaired

-
Imagem
By   Jestine Yong   on November 21, 2013 2   The problem of this receiver was a bad picture. In order to make sure that the LNB DISH and Signal Cable are working fine, I installed another good receiver to the end of the line and I received a very beautiful and sharp picture and this indicated the LNB dish all the way down to receiver were working fine. This means the problem for sure is the receiver set. Note:  LNB stands for  low-noise block  and the function is to  receive the very low level microwave signal from the satellite, amplifies it, changes the signals to a lower frequency band and sends them down the cable to the indoor receiver unit. After opening the cover, the first thing I checked was the output voltages from power supply. More or less all of the output voltages readings were within tolerance:   5 v     was    5.17       3.3        ” ...
Leia mais